ColinMacKenzie.net

Electronics

Verilog Source

There are two areas in our design reguired to implement simple pipelining. (1) We must remove the outer state machine so instead of sequencing through the four instruction cycles each one is executed in parallel. (2) To link each cycle together like a pipelining assembly line we must also add some register storage in between to store the result from each cycle until the next cycle occurs.

module yfcpu(clk, rst, PC);

// our cpu core parameters
parameter im_size = 8;		// 2^n instruction word memory
parameter rf_size = 4;		// 2^n word register file

// a parameter for the bus width of our cpu
parameter bw = 8;

input clk;	// our system clock
output PC;	// our program counter
input rst;	// reset signal

// the cycle states of our cpu, i.e. the Control Unit states
parameter s_fetch   = 3'b000;	// fetch next instruction from memory
parameter s_decode  = 3'b001;	// decode instruction into opcode and operands
parameter s_execute = 3'b010;	// execute the instruction inside the ALU
parameter s_store   = 3'b011;	// store the result back to memory
parameter s_nostore = 3'b100; // dont store any result, skips a cycle

// the parts of our instruction word
parameter opcode_size = 4;		// size of opcode in bits

// Mnemonic Op Codes
parameter LRI   = 4'b0001;
parameter ADD   = 4'b0100;
parameter SUB   = 4'b0101;
parameter OR    = 4'b0110;
parameter XOR   = 4'b0111;

// our new branch mnemonics!
parameter BRA    = 4'b1000;   // branch to address in memory location RB
parameter BRANZ  = 4'b1001;   // branch to address in memory location RB, if RA is zero
parameter BRAL   = 4'b1010;   // branch to literal address RB
parameter BRALNZ = 4'b1011;   // branch to literal address RB, if RA is zero
parameter CALL   = 4'b1100;   // call subroutine; store current PC into RD and jump to address in literal location RB

parameter HALT  = 4'b1111;



// our memory core consisting of Instruction Memory, Register File and an ALU working (W) register
reg [ opcode_size + (rf_size*3) -1 : 0 ] IMEM[0: (1 << im_size) -1 ] ;	// instruction memory
reg [ bw-1:0 ] REGFILE[0: (1 << rf_size) -1 ];	// data memory
reg [ bw-1:0 ] W;	// working (intermediate) register

// our cpu core registers
reg [ im_size-1 : 0 ] PC;			// program counter
reg [ opcode_size + (rf_size*3) -1 : 0 ] IR;	// instruction register

/* Control Unit registers
     The control unit sequencer cycles through fetching the next instruction
     from memory, decoding the instruction into the opcode and operands and
     executing the opcode in the ALU.
*/
reg [ 2:0 ] current_state;
reg [ 2:0 ] next_state;

// our instruction registers
// an opcode typically loads registers addressed from RA and RB, and stores
// the result into destination register RD. RA:RB can also be used to form
// an 8bit immediate (literal) value.
reg [ opcode_size-1 : 0 ] OPCODE;
reg [ rf_size-1 : 0 ] RA;   // left operand register address
reg [ rf_size-1 : 0 ] RB;   // right operand register address
reg [ rf_size-1 : 0 ] RD;   // destination register


/* Pipeline flags */
reg F_STORE;	// execute cycle sets if W should be written to RD in writeback cycle
reg F_HALTED;	// if set, we halt execution until a reset instruction (in a sim, we finish)

// the initial cpu state bootstrap
initial begin
	PC = 0;
	current_state = s_fetch;

	// LOADROM: here we load the rom file generated by our assembler!!!
	$readmemh("test.rom",IMEM,0,14);

	wait(OPCODE == HALT) $writememh("regfile",REGFILE);
	end




// at each clock cycle we sequence the Control Unit, or if rst is
// asserted we keep the cpu in reset.
always @ (clk, rst)
begin
	if(rst) begin
		current_state = s_fetch;
		PC = 0;
		F_HALTED = 0;
		end
	else if(!F_HALTED)
	   begin
	   // perform a fetch, decode, execute and writeback cycle concurrently
		// FETCH :  fetch instruction from instruction memory
		IR = IMEM[ PC ];
		PC = PC + 1; 	// increment program counter (instruction mem pointer)

		// DECODE : decode the opcode and register operands
		OPCODE = IR[ opcode_size + (rf_size*3) -1 : (rf_size*3) ];
		RA = IR[ (rf_size*3) -1 : (rf_size*2) ];
		RB = IR[ (rf_size*2) -1 : (rf_size  ) ];
		RD = IR[ (rf_size  ) -1 : 0 ];

		// EXECUTE : Execute ALU instruction, process the OPCODE
		case (OPCODE)
			LRI: begin	
			   // load register RD with immediate from RA:RB operands
			   W = {RA, RB};
			   F_STORE = 1;
			   end
					   
			ADD: begin	
			   // Add RA + RB
			   W = REGFILE[RA] + REGFILE[RB];
			   F_STORE = 1;
			   end
						
			SUB: begin	
			   // Sub RA - RB
			   W = REGFILE[RA] - REGFILE[RB];
			   F_STORE = 1;
			  end

			OR: begin	
			   // OR RA + RB
			   W = REGFILE[RA] | REGFILE[RB];
			   F_STORE = 1;
			   end
						
			XOR: begin	
			   // Exclusive OR RA ^ RB
			   W = REGFILE[RA] ^ REGFILE[RB];
			   F_STORE = 1;
			   end
						
			HALT: begin
			   // Halt execution, loop indefinately
			   F_HALTED = 1;
			   $finish;	// quit the sim
			   end
						
			BRA: begin
			   // branch to REGFILE[RB]
			   PC = REGFILE[RB];
			   F_STORE = 0;
			   end

			BRAL: begin
			   // branch to RB
			   PC = RB;
			   F_STORE = 0;
			   end
						
			BRANZ: begin
			   // branch to REGFILE[RB] if REGFILE[RA] is zero
			   if(REGFILE[RA] !=8'd0)
			      PC = REGFILE[RB];
			   F_STORE = 0;
			   end

			BRALNZ: begin
			   // branch to RB if REGFILE[RA] is zero
			   if(REGFILE[RA] !=8'd0)
  			      PC = RB;
			   F_STORE = 0;
			   end
						
			CALL: begin
			   // call a subroutine; store PC into RD and jump to location in REGFILE[RB]
			   W = PC;
			   PC = RB;
			   F_STORE = 1;
			   end
						
			   // catch all : NOP!
			default: begin 
			   F_STORE = 0;
			end
		endcase
			
		// STORE : store the ALU working register into the destination register RD
		if(F_STORE)
			REGFILE[RD] = W;

      // move the control unit to the next state
	end
end

endmodule

User Rating: / 56
PoorBest